Hayward Pool Heater Error Codes: Causes, Troubleshooting, and Common Fixes

A pool heater is one of the best ways to extend your swimming season, especially during cooler mornings and evenings in Austin and Central Texas.

When a Hayward pool heater stops working, the control panel often displays an error code or operating message to help identify the issue. These diagnostic messages are designed to protect the heater and guide troubleshooting.

Understanding what these codes mean can help pool owners identify simple problems, perform basic checks, and know when professional service is needed.

This guide covers common messages found on:

  • Hayward H-Series pool heaters
  • Hayward Universal H-Series pool heaters

and explains:

Before Troubleshooting Your Hayward Pool Heater

Before focusing on specific error codes, check these basic items.

Confirm Proper Water Flow

Many Hayward heater problems are caused by insufficient water flow.

Verify:

  • Pool pump is running
  • Filter is clean
  • Pump basket is clear
  • Valves are positioned correctly
  • Return jets have strong water flow

Pool heaters include safety systems that prevent operation when water flow is too low.

Check Your Pool Filter

A dirty filter can restrict circulation and cause heater shutdowns.

Check:

  • Filter pressure
  • Cartridge condition
  • Sand filter cleanliness
  • D.E. filter condition

Maintaining proper water flow is one of the most important parts of heater operation.

Verify Heater Settings

Confirm:

  • Heater power is on
  • Desired temperature is above current water temperature
  • Pool automation is requesting heat
  • Correct pool or spa mode is selected

Hayward Heater BO Code: What Does It Mean?

BO Is Not an Error Code

One of the most misunderstood messages on Hayward pool heaters is the BO code.

Unlike codes such as:

  • IF (Ignition Failure)
  • LO (Low Flow/Limit Issue)
  • SF (Sensor Failure)

the BO message does not indicate a heater malfunction.

BO means “Bypass Operation” and indicates the heater has been placed into a special operating mode where normal temperature control is temporarily bypassed.

This mode is typically used for:

  • Diagnostic testing
  • Service procedures
  • Troubleshooting
  • Temporary heater operation during evaluation

Why Is My Hayward Heater Showing BO?

The BO message usually appears when the heater has been placed into bypass operation through the control interface.

This may happen intentionally during:

  • Heater servicing
  • Diagnostic checks
  • Control adjustments

It can also occur if settings are changed accidentally.

How Do I Remove the BO Code on a Hayward Heater?

In many cases, the BO message can be cleared by returning the heater to normal operating mode.

General steps:

  1. Turn the heater off.
  2. Allow the control panel to reset.
  3. Verify the heater is set to normal operating mode.
  4. Turn the heater back on.

The exact procedure can vary depending on the Hayward heater model and control board version.

Does the BO Code Mean My Hayward Heater Is Broken?

No.

The BO message by itself does not mean the heater needs repair.

However, if the heater:

  • Will not return to normal operation
  • Does not heat the pool
  • Displays other fault codes
  • Repeatedly enters bypass mode

then additional troubleshooting may be required.

Common Hayward Pool Heater Error Codes

Hayward heater codes vary slightly by model and control system, but many common issues overlap across H-Series and Universal H-Series models.

Hayward Heater Error Code: IF (Ignition Failure)

What It Means

The heater attempted to ignite but was unable to establish a proper flame.

This is one of the most common Hayward heater problems.

Common Causes

Possible causes include:

  • Gas supply issue
  • Ignition system problem
  • Dirty burner assembly
  • Flame sensing issue
  • Blocked airflow
  • Electrical connection issue

Basic Checks

Before calling for service, verify:

  • Gas supply is available
  • Other gas appliances are operating normally
  • Heater intake and exhaust areas are clear
  • Power supply is stable

If the heater repeatedly attempts ignition and fails, professional diagnosis is recommended.

Hayward Heater Error Code: LO (Limit or Flow Issue)

What It Means

The heater is detecting a problem with water flow or a safety limit.

Common Causes

  • Dirty filter
  • Low pump speed
  • Closed valve
  • Air entering the plumbing system
  • Faulty pressure switch
  • Temperature limit issue

Common Fixes

Try:

  1. Clean the pool filter.
  2. Empty pump and skimmer baskets.
  3. Confirm valves are open.
  4. Verify pump operation.
  5. Increase pump speed if using a variable-speed pump.

If the error remains, a flow switch, pressure switch, or sensor may need testing.

Hayward Heater Error Code: SF (Sensor Failure)

What It Means

The heater is detecting a problem with one of its temperature sensors.

Common Causes

  • Failed temperature sensor
  • Loose wiring connection
  • Corrosion
  • Damaged sensor cable

Common Fixes

Check:

  • Sensor connections
  • Wiring condition
  • Signs of moisture damage

A failed sensor typically requires replacement.

Hayward Heater Error Code: HS (High Temperature Sensor)

What It Means

The heater has detected an excessive temperature condition.

The safety system shuts the heater down to prevent damage.

Common Causes

  • Low water flow
  • Dirty filter
  • Scale buildup
  • Incorrect valve position
  • Faulty temperature sensor

Common Fixes

Check:

  • Pool circulation
  • Filter pressure
  • Pump operation
  • Water chemistry

In Central Texas, mineral buildup from hard water can contribute to reduced heater performance over time.

Hayward Heater Error Code: CE (Communication Error)

What It Means

The heater is having trouble communicating with an external controller or internal control components.

Common Causes

  • Automation communication issue
  • Wiring problem
  • Control board issue
  • Incorrect configuration

Common Fixes

Check:

  • Automation connections
  • Controller settings
  • Power cycle the system

If communication problems continue, professional diagnosis may be required.

Hayward Heater Error Code: AC (Airflow Fault)

What It Means

The heater is detecting a combustion airflow problem.

Possible Causes

  • Blocked exhaust
  • Blocked intake
  • Blower problem
  • Pressure switch issue

Common Fixes

Inspect:

  • Heater vents
  • Intake openings
  • Equipment area around the heater

Never operate a heater with blocked combustion airflow.

Hayward Heater Error Code: PF (Power Failure)

What It Means

The heater has detected an electrical power problem.

Common Causes

  • Power interruption
  • Circuit breaker issue
  • Loose connection
  • Electrical supply problem

Common Fixes

Check:

  • Breaker status
  • Heater disconnect
  • Power supply

If electrical problems continue, a qualified technician should inspect the system.

Common Hayward Heater Problems Beyond Error Codes

Not every heater problem produces an error code.

Hayward Heater Turns On but Does Not Heat

Possible causes:

  • Gas supply problem
  • Dirty burners
  • Water flow issue
  • Faulty temperature sensor
  • Heat exchanger issue

Hayward Heater Starts Then Shuts Off

Common causes:

  • Low water flow
  • Overheating condition
  • Flame loss
  • Sensor problem

Hayward Heater Has Low Heat Output

Possible causes:

  • Dirty filter
  • Incorrect gas supply
  • Scaling inside heat exchanger
  • Incorrect heater sizing

Common Hayward Heater Problems in Austin, Texas

Hard Water and Calcium Scale

Austin-area water contains minerals that can accumulate inside pool equipment.

Central Texas pool owners face several conditions that can affect heater performance.

Over time, scale can contribute to:

  • Reduced heat transfer
  • Lower efficiency
  • Flow restrictions
  • Heater shutdowns

Maintaining proper:

  • pH
  • Calcium hardness
  • Total alkalinity

helps protect heater components.

Variable-Speed Pump Settings

Many modern pools use variable-speed pumps.

If pump RPM is set too low, the heater may not receive enough water flow to operate.

A common troubleshooting step is verifying that the pump speed meets the heater’s minimum flow requirements.

Seasonal Startup Issues

After periods of limited use, heaters may experience:

  • Ignition issues
  • Sensor problems
  • Gas supply issues
  • Startup failures

A preseason equipment inspection can help identify problems before the swimming season begins.

How to Reset a Hayward Pool Heater

A basic reset may clear temporary faults.

General reset steps:

  1. Turn the heater off.
  2. Turn off power to the heater.
  3. Wait several minutes.
  4. Restore power.
  5. Attempt normal operation.

If the same error code returns, the underlying issue still needs to be addressed.

Repeated resets without diagnosis can allow a small problem to become a larger repair.

When Should You Call a Professional?

Pool heaters combine:

  • Gas systems
  • Electrical components
  • Combustion systems
  • Safety controls

Professional service is recommended when:

  • Ignition repeatedly fails
  • You smell gas
  • Error codes return after basic checks
  • The heater cycles on and off
  • Sensors or control boards need replacement
  • Internal components require testing

Frequently Asked Questions

Why does my Hayward pool heater say IF?

The IF code means the heater failed to ignite. Common causes include gas supply issues, ignition problems, airflow issues, or flame sensing problems.

Why does my Hayward heater say LO?

The LO code usually indicates a low-flow or limit issue. Common causes include dirty filters, low pump speed, closed valves, or flow sensor problems.

Why does my Hayward heater say BO?

The BO message is not an error code. It means the heater is in Bypass Operation mode, which temporarily bypasses normal temperature control for diagnostics or service.

How long do Hayward pool heaters last?

With proper maintenance, many Hayward pool heaters last approximately 7–12 years depending on usage, installation, water chemistry, and environmental conditions.

Can low pump speed prevent a Hayward heater from working?

Yes. Variable-speed pumps operating at low RPM may not provide enough water flow to satisfy the heater’s safety requirements.

Keep Your Hayward Pool Heater Running Efficiently with Aqua Clear Pool Care

A Hayward pool heater is a valuable investment that allows you to enjoy your pool more months of the year. When error codes or operating messages appear, understanding what they mean can help you identify simple issues and avoid unnecessary downtime.

At Aqua Clear Pool Care, we help homeowners throughout Austin, Round Rock, Cedar Park, Georgetown, Leander, Pflugerville, Lakeway, Bee Cave, Dripping Springs, and surrounding Central Texas communities diagnose and repair pool equipment problems.

From pool heaters and pumps to automation systems, filters, and water chemistry, our team helps keep your pool operating efficiently and reliably throughout the year.

Related Blog Posts

Leave a Reply